分享～6,5,4,2,1channel Amplifier～ ～仪器与喇叭质料区～!!

Ah_Tat

哈哈。。。。
Audison最棒。。。。！！！

fredi兄。。。
你很得空啊。。。？
突然间来放毒。。。。
不要害新手啦。。。。

fredi1987

其实 我一路忙着一路放的！
你没有看到我 编辑 吗？ 不少次了！

尤其是你的audison 最复杂弄。


哈哈，因为给人家了解多点4ch.. 要什么的。。 直接来这里选，然后去买回来！

fredi1987

原帖由 ICEland 于 23-1-2007 06:41 PM 发表


奇怪怎么放这么普通的东西？！
这个普通牌子这系列不止这三粒 amp 咧！

那个 只是普通白色而已。。
得空在放~

kudoshinichimy

原帖由 ICEland 于 23-1-2007 05:20 PM 发表


也是和你一样标回来的！

哇！幸好我还没给钱，这款amp到底哪里不好？因为它的watt也很大啊......
Output Power (max): 2900W (350W X 4, 1500W X 1 load 4 ohms)
    * Nominal Power (RMS): 150WRMS X 4, 500WRMS X 1 load 4 ohms
    * Bridged output power (max): 1400 Watts (700W X 2 load 4 ohms)

fredi1987

原帖由 kudoshinichimy 于 23-1-2007 11:55 PM 发表


哇！幸好我还没给钱，这款amp到底哪里不好？因为它的watt也很大啊......
Output Power (max): 2900W (350W X 4, 1500W X 1 load 4 ohms)
    * Nominal Power (RMS): 150WRMS X 4, 500WRMS X 1 load 4 oh ...

4ch 可以 briged 1ch 出的灭？     不是2ch 出吗？

consrito

The Helix B2 is a powerful, dynamic top-of-the-class amplifier that is controlled by its own integrated software. This integrated managing software (IMS) makes the read-out of all relevant data possible. Therefore the amplifier provides optimized working in terms of power, current and temperature. The music signal is of course analog processed to reach the best sound and dynamic results. The sophisticated active crossover allows a perfect adjustment of all connected speakers and subwoofers. The B2 has an integrated temperature controlled cooling fan that can be switched off if desired. The turn-on temperature as well as the maximum power of the cooling fan can be adjusted by two separate controls. The connection of an external fan is possible.

Driver with class A technology Outputstage with 16 MosFet transistors RMI (realmixed input) for forming an optimised mono-summation signal from the left and right channels NFI (noisefree input) for distortion-free listening L Intelligent active crossover Mono/Bridged/ Stereo switch 8.0 volt input for connection to any signal source ADC - Anti Distortion Choke to eliminate distortions Intelligent power supply Separate speaker protection circuit with current limitation for speaker short-circuiting, cable contact with car chassis, low impedance and wrong connection CPS - Color Protection System SMD - Surface Mounting Devices for constant assembling quality Double-sided, copper plated pc-board for best power and signal transmission and protection against vibrations 24-karat gold-plated solid connectors Temperature-optimised heatsink for highest efficiency 1% accurate components for perfect audiophile sound quality and maximum power Smoked-grey plexi cover with both side printing Technical Data: Cont. power rating RMS / Musik an 2 x 4Ohm at 12 Volt 2 x 80 Watt Cont. power rating RMS / Musik at 2 x 4Ohm an 13,8 Volt 2 x 100/165 Watt Cont. power rating RMS / Musik at 2 x 2Ohm at 13,8 Volt 2 x 180/300 Watt Cont. power rating RMS/Musik 1 x 4 Ohm gebrückt 1 x 360/600 Watt Adjust Highpass/Lowpass/Bandpass 15 Hz - 3kHz Total harmonic distortion (TDH) < 0,014% Signal to noise ratio > 96 dB Damping factor > 450 Frequency range 20 Hz -20 kHz +/- 0,5 dB TIM Distortion < 0,02% Input sensitivity 500 mV - 8 V Fuse 2 x 20 A Input impedance 10 kOhm Dimensions (H/W/D) in mm 35 x 240 x 300 Weight netto 3,1 kg

[ 本帖最后由 consrito 于 25-1-2007 12:38 AM 编辑 ]

consrito

Driver with class A technology Outputstage with 24 MosFet transistors RMI (realmixed input) for forming an optimised mono-summation signal from the left and right channels NFI (noisefree input) for distortion-free listening Intelligent active crossover Bass Boost Control 0-9 dB, adjustable center frequencies 30-120 Hz Mono/Bridged/ Stereo switch 8.0 volt input for connection to any signal source ADC - Anti Distortion Choke to eliminate distortions Intelligent temperature and power controlled switching power supply Separate speaker protection circuit with current limitation for speaker short-circuiting, cable contact with car chassis, low impedance and wrong connection CPS - Color Protection System SMD - Surface Mounting Devices for constant assembling quality Double-sided, extra strong (2x 110u) and copper plated pc-board for best power and signal transmission and protection against vibrations 24-karat gold-plated solid connectors suitable for 25 m&sup2;/ gauge 4 cables Temperature-optimised heatsink for highest efficiency 1% accurate components for perfect audiophile sound quality and maximum power Smoked-grey plexi cover with both side printing Technical Data: Cont.power rating RMS/max. power at 2x4 Ohms measured at 12 V 2 x 120 Watt Cont.power rating RMS/max. power at 2x4 Ohms measured at 13,8 V 2 x 150/250 Watt Cont.power rating RMS/max. power at 2x2 Ohms measured at 13,8 V 1 x 270/450 Watt Cont.power rating RMS/max. power at 2x1 Ohms measured at 13,8 V 2 x 395/650 Watt Cont.power rating RMS/max. power at 1x4 Ohms bridged 1 x 540/900 Watt Cont.power rating RMS/max. power at 1x2 Ohms bridged 2 x 790/1300 Watt Adjust Highpass/Lowpass/Bandpass 15 Hz - 6kHz Total harmonic distortion (THD) < 0,009% Signal to noise ratio > 100 dB Damping factor > 450 Frequency range 20 Hz -20 kHz TIM Distortion < 0,016% Input sensitivity 500 mV - 8 V Fuse 4 x 20 A Input impedance 10 kOhm Bassboost adjustable 0 - 9 dB More informationen for Official Dealers in the LOGIN-Area. 35 x 240 x 432 Weight netto 4,7 kg

[ 本帖最后由 consrito 于 24-1-2007 12:43 AM 编辑 ]

consrito

Orion HCCA 250 G5

Output Power at 12V, 20Hz &#8764; 20kHz, <0.1% THD:
2 x 50W @ 4 ohm
2 x 100W @ 2 ohm
2 x 200W @ 1 ohm
2 x 400W @ &frac12; ohm
1 x 200W @ 4 ohm bridged
1 x 400W @ 2 ohm bridged
1 x 800W @ 1 ohm bridged
THD: <0.1% (20Hz &#8764; 20kHz)
S/N Ratio: >100dB (full bandwidth @ rated power)
Damping Factor: >400 (full bandwidth)
Freq. Response: 20Hz &#8764; 20kHz (±0.25dB)
Linear Bandwidth: 6Hz &#8764; 50kHz (±3dB)
Fuse: 2 x 30A
Dimensions: 18" x 10.25" x 2.25" (45.7cm x 26cm x 5.7cm)

consrito

TRU SH-1 Sledge Hammer

1 x 2000W @ 4 ohms
1 x 3000W @ 2 ohms
1 x 4000W @ 1 ohm
THD: <0.1%
S/N Ratio: >100dB
Damping Factor: >700
Efficiency: 69.1%
Freq. Response: 10Hz &#8764; 300Hz (+/- 1dB)
Fuse: External 2 x 120A
Dimensions: 15" x 8.8" x 6.75" (38.1cm x 22.4cm x 17.2cm)
Weight: 23.5 lbs. (10.7 kg.)

consrito

TRU TO3-4.150

4 x 150W @ 4ohms
4 x 250W @ 2ohms
2 x 500W @ 4ohms bridge
Fuse: External 120A

consrito

Sinfoni AMPLItude 150.2x

2 x 165W @ 4 ohms (12V / 13.8V)
2 x 294W @ 2 ohms (12V)
2 x 315W @ 2 ohms (13.8V)
1 x 590W @ 4 ohms bridged (12V)
1 x 635W @ 4 ohms bridged (13.8V)
1 x 775W @ 2 ohms bridged (12V)
1 x 925W @ 2 ohms bridged (13.8V)

fredi1987

B2 helix..  80x2ch AMP

照片 为何放了B4 的？

mooscar618

我现在用着F545, 2CH 打COMPONENT, 剩下的2CH BRIDGE 1CH 以后有300RMS, 还有一架M301, 有150RMS, 各位大大觉得我应该用哪一架来打SUB呢?

我不懂怎么比较, 一架是BRIDGE起来的, 一架是MONO的. 是看机种还是要看它们的RMS?

ALPINE MRV-F545


4/3/2 Channel Operation

• Amplifier Link Ready
• DC-DC PWM Power Supply
• Discrete Pre-Amp Stage
• Gold Plated RCA Input Connectors
• Input Mode Selector Switch
• MOSFET Power Supply
• MultiMode
• Non-Fading Pre-Amp Output
• STAR Circuitry
• Solid Copper Bus Bars
• Bass Engine&reg;
• Crossover Network : 30Hz-200Hz HP / LP (12dB/oct)
• Tuned Bass EQ (Variable) : 45Hz +16dB (Ch-3/4)

General

• Frequency Reponse : 10Hz-50kHz (+0,-1dB)
• Heat Sink (WxHxD)in : 16-1/2” x 2-5/16” x 8-11/16”
• Heat Sink (WxHxD)mm : 420mm x 60mm x 220mm
• Input Impedance : 10k ohm
• Input Sensitivity (for rated power) : 0.2 V to 4.0V
• Power Requirements : 14.4V DC (11V to 16V)
• Signal to Noise (S/N) : 96dBA (referenced to rated power)
• Slew Factor : greater than 5
• Speaker Impedance : 4 or 2 ohms(stereo), 4 ohms(bridged)
• Weight : 4.0kg.

RMS Power (at 12V,20Hz-200Hz)

• Bridged 4 ohms : 300W x 1 (Ch-3/4)
• Per channel into 2 ohms : 150W x 2 (Ch-3/4)
• Per channel into 4 ohms : 100W x 4
• RMS Power (at 14.4V,20Hz-200Hz)
• Bridged 4 ohms : 125W x 1 (Ch-3/4), 500W x 1 (Ch-3/4)
• Per channel into 2 ohms : 250W x 2 (Ch-3/4)

ALPINE MRD-M301


-MAX Power: 600W x 1(2Ohm)
-350W x 1 RMS [2 &#8486; @14.4V (1%THD)]
-175W x 1 RMS [4 &#8486; @14.4V (1%THD)]
-250W x 1 RMS [2 &#8486; @12V (1%THD)]
-150W x 1 RMS [4 &#8486; @12V (1%THD)]
-Fully Digital Class-D Technology
-Digital Control Centre with LED Information Display (Temperature, Voltage, Current)
-Bass Engine DSP (Parametric EQ, Crossover,Time Correction, Phase Control, Subsonic Filter, Bass Compensation)
-Integrated Wire Covers
-Variable Turn-On Delay
-Memory Preset
-Thermal Management
-Safe Mode
-Amplifier link / Remote Amplifier Control Centre Ready

Ah_Tat

fredi兄。。。
你这个贴弄整齐点。。。
好像一个牌子然后放完进去一个地方。。。（最好是全部series）
然后放多一点amp的牌子。。。

我觉得。。。
这个贴可以上精华。。。
可以方便很多新手要买amp的时候在这里找。。。
然后这里的大大可以给意见。。。。

fredi1987

原帖由 Ah_Tat 于 24-1-2007 05:29 PM 发表
fredi兄。。。
你这个贴弄整齐点。。。
好像一个牌子然后放完进去一个地方。。。（最好是全部series）
然后放多一点amp的牌子。。。

我觉得。。。
这个贴可以上精华。。。
可以方便很多新手要买amp的时 ...

放太多 很 lag... 我更本laoding不到 照片出来。
现在都lag 了 很多张laod 不到。

我打算有些del 搬过来~ 这里

原帖由 mooscar618 于 24-1-2007 05:09 PM 发表
我现在用着F545, 2CH 打COMPONENT, 剩下的2CH BRIDGE 1CH 以后有300RMS, 还有一架M301, 有150RMS, 各位大大觉得我应该用哪一架来打SUB呢?

我不懂怎么比较, 一架是BRIDGE起来的, 一架是MONO的. 是看机种还是 ...

F545 briged 起来也是 150rms... 4ohm..

你用M301 会比较好！

[ 本帖最后由 fredi1987 于 24-1-2007 06:04 PM 编辑 ]

fredi1987

High power and versatility are the main features of this four channel amplifier. Its two pairs of channels and its pre output can be configured as you like, simply acting on the switches of its built-in module. VRx 4.300 sound can be perfected or customised by adding one or more Control Extensions: it has one pin socket for PC36, one for SM24 and two for PRM3 (one for every pair of channels).


-------------------------------------------------------------------------------------






Among the most powerful stereo amplifiers in the marketplace, VRx 2.400 excels in driving big midwoofer sections, yet showing unique refinement and outstanding musical qualities when used for driving complete systems with passive crossover. A real champion. One pin socket for Multichannel Extensions (HL12, BH12, LM24, HL24 or BSA1) and three for Control Extensions (PC36, SM24 and PRM3) insure the widest choice of configurations and calibration.


-------------------------------------------------------------------------------------






VRx line most powerful amplifier is especially designed for driving subwoofers. The wide choice of configurations and tuning insured by Multichannel Extensions (HL12, LM24, HL24 or BSA1) and Control Extensions (PC36, SM24, DSC1 and PRM3) makes VRx 1.500 the most complete and cutting-edge amplifier for subwoofers. When you need even higher powers, you can connect two VRx 1.500 in bridge, achieving 2000 W RMS on 4 Ohms and 4000 W RMS on 2 Ohms.



======================================================================






&#8226; Limit Led
&#8226; On/Off Led
&#8226; Safety Led
&#8226; Subsonic Bypass
&#8226; A and B channels adjustment
&#8226; Lo-Pass filter slope adjustment: 12/24 dB
&#8226; Crossover frequencies adjustment:
Hi/Bypass, Lo/Bypas

Configuration switches:
&#8226; Crossovers bypass
&#8226; 1 IN+Pre Out/2 IN.
Subsonic filter frequency setting.
VCA module insertion for sub volume remote control.

LRx 4.300 is a high power, very compact four channel amplifier. It can provide 65W continuous power per channel at 4 Ohms and 105W at 2 Ohms; if it is used in mono, power increases up to 210W, available on two channels. It is perfect to make complete high sound quality Front/Sub systems or to properly handle the upper ways of multi-amplified ones, attaining very high SPL values. It has two inputs, two Hi-Pass and Lo-Pass Butterworth crossovers with independent adjustments and one subsonic filter; all filters can be bypassed. Lo-Pass can be configured at 12dB/Oct. stereo in multiamplified systems and at 24dB/Oct. mono in Front/Sub ones.



-------------------------------------------------------------------------------------








&#8226; Limit Led
&#8226; On/Off Led
&#8226; Safety Led
&#8226; Amp:Hi/Lo-Pass for selecting output signal and Pre Out one
&#8226; Levels adjustment
&#8226; Crossover frequency range selection (x1 - x10)
&#8226; Hi/Lo-Pass crossover frequency adjustment
&#8226; Crossover frequencies adjustment: Hi/Bypass, Lo/Bypass
&#8226; Mode (Mono/Stereo)

Extremely small size, extraordinary musical performances, exceptional energy reserve. LRx 2 amplifiers have very high current supply capacity to easily drive even the most difficult loads and thrilling power, for all needs. If used alone, they are especially suitable to handle exacting, good quality speakers systems; if employed in several units, they are the best to build multi-amplification systems with very high SPL values. They have a double bypass Hi/Lo-Pass Butterworth crossover for driving multiamplified or subwoofer systems.


-------------------------------------------------------------------------------------






&#8226; Limit Led
&#8226; On/Off Led
&#8226; Safety Led
&#8226; Subsonic Bypass
&#8226; Output level adjustment
&#8226; Phase inverter (0°-180°)
&#8226; F1Q: Lo-Pass filter Q factor adjustment
&#8226; Crossover frequencies adjustment:
Hi/Bypass, Lo/Bypass

LRx 1.400 is a mono amplifier especially designed to drive very low loads with thrilling energy reserve, built-in active filters and LRx typical compact size. Power supply and final stages use high current MOSFETs, which satisfy every power need. With its 900 watts at 1 Ohm, LRx 1.400 is the ideal amplifier to drive state-of-the-art subwoofers systems and to realise installations with very high SPL values and excellent timbre quality. It has a Hi-Pass stereo filter and a 24dB/Oct. Lo-Pass mono one; both are Butterworth, with independent adjustments. The subwoofer section has a bypass subsonic filter and a 24dB/Oct. slope one with Q factor adjustment and phase switch; thus, it always allows you to take full advantage of any speaker you are using.

[ 本帖最后由 fredi1987 于 26-1-2007 01:52 PM 编辑 ]

ah_siau

原帖由 fredi1987 于 24-1-2007 05:35 PM 发表

放太多 很 lag... 我更本laoding不到 照片出来。
现在都lag 了 很多张laod 不到。

我打算有些del 搬过来~ 这里

放多多来毒人家

mooscar618

原帖由 fredi1987 于 24-1-2007 05:35 PM 发表

F545 briged 起来也是 150rms... 4ohm..

你用M301 会比较好！

不是很会看他的SPEC, 但是我记得是有300RMS的...

consrito

原帖由 fredi1987 于 24-1-2007 01:04 AM 发表
B2 helix..  80x2ch AMP

照片 为何放了B4 的？

放错了..现在改掉..

MinTze

原帖由 mooscar618 于 24-1-2007 05:09 PM 发表
我现在用着F545, 2CH 打COMPONENT, 剩下的2CH BRIDGE 1CH 以后有300RMS, 还有一架M301, 有150RMS, 各位大大觉得我应该用哪一架来打SUB呢?

我不懂怎么比较, 一架是BRIDGE起来的, 一架是MONO的. 是看机种还是 ...

当然是分开amp比较好，这样改天你可以full active。你的301power不是很大，可能找sub配合方面会比较困难。